facebookInstagramTikTokYou Tube

Superior Radius Arms Standard Height Suitable For Land Rover Range Rover (Series 1) (Pair) - LDRDRAMSTD

Brand:  Superior Engineering Product ID:  21360
SKU:  LDRDRAMSTD

$1,100.00  (Pair)

Supply Only Price.

-+
|

600% Stronger then H-Beam Radius Arms

Street Legal under ADR NCOP

Lifetime Warranty

This is a pair of heavy duty Superior Engineering dropped Radius Arms Suitable For Land Rover Range Rover (Series 1) with a standard height lift.

Superior Engineering has developed the ultimate in Drop Radius Arms for Landover's.

Designed and Manufactured to take your vehicles offroad driving performance to a new level! And the visual appearance of these new Radius Arms make a statement like no other.

Our Radius arms not only correct castor angles after performing a suspension lift, but also utilise standard OE spec Nissan Patrol rubber bushes in the Radius arms.

These features allow for increased Articulation as well as better road manners and eliminate the need to use expensive Poly aftermarket bushes that are considered inferior to OE style rubber bushes.

The Superior Engineering Radius Arm design will also permit you to run a Superior Engineering Radius arm Spacer washers to push the front diff forward, increasing clearance and achieving a better Approach angle.

Superior Engineering supplies all of our radius arms with the Rubber bushes pressed in for your convenience, and you will also be supplied with genuine Nissan rear radius arm bushes and washers.

Benefits of Superior Drop Radius Arms

  • Manufactured from 32mm High Tensile Plate
  • High Tensile Pivot Bush pin
  • 16mm UNF fine thread
  • Rubber Bushes pre-fitted into arms
  • Laser cut and CNC machined to precise measurements and caster location
  • Authentic Superior Engineering Logo CNC machined into side of Arms
  • Manufactured Suitable For various lifts
  • Sand blasted with rust prevention applied
  • Powder Coated for maximum durability and finish
  • High Tensile Plate for the ultimate in durability, will not crack like Cast Radius Arms

    • Pair of Drop Radius Arms

    Superior Radius Arms Standard Height Suitable For Land Rover Range Rover (Series 1) (Pair) - LDRDRAM2

    Fig. 1 shows the Superior Arm deflecting only 4.1mm under load with real world load points.
    Fig. 2 shows the Competitor's Arm deflecting 24.91mm under the same load points and loads, almost the same as the width of the Arm itself.
    Also of note is the Competitor's Arm deflected to a point that may cause metal fatigue over time, which may lead to total failure.

     

     

    Below is a comparison chart showing different forms of Castor correction and how they compare in Cost, Flex, Handling and Offroad Ability.

    Suspension component performance chart

     
    Genuine/Non Genuine – Advertised parts are not genuine (unless specifically stated) and manufacturer references are for application purposes only. Only items that are specifically noted as Genuine OEM can be presumed as genuine parts.

    Superior Engineering is not sponsored, approved, affiliated or otherwise associated with any genuine or original parts manufacturer, distributor or dealer.


    Identification and Guidance Only – Photos are for identification purposes only and may be of either genuine or non-genuine parts.
    All manufacturers names, symbols and descriptions on this website are used for reference purposes only, and it is not implied that any units or parts listed is the product of these manufacturers.

    Original Equipment Manufacturer "OEM" part/reference numbers are listed for information/reference purposes only. Trademarks identifying these parts are those of each OEM and are the property of their owners and are not used, or authorized for use, by Superior Engineering. Cross-referenced parts from the Original Equipment Manufacturer "OEM" are listed for information purposes only.

    Superior Engineering has no associations and/or claims to be associated with OEM Vehicle Manufacturers and their Companies worldwide. Any implied associations are purely coincidental and are not inferred. Superior Engineering is a supplier of fully interchangeable non-genuine spare parts (alternatives) for equipment produced by manufacturers using in accordance with law OEM Vehicle Manufacturers and their products, i.e. suspension parts, steering components, manufactured items, vehicle accessories etc. Alternative spare parts produced by Superior Engineering are manufactured according own technological documentation developed with the use of reverse engineering.
    Vehicle Information
    Lift Height0-2 inch